串口透傳

• “透傳”通常指的是數據的透明傳輸，意思是在不對數據進行任何處理或修改的情況下，將數據從一個接口轉發到另一個接口。
• 值得注意的是要避免串口之間無限制的透明，可以采用互斥鎖的方式進行限制
• 使用方法

1. 對USART1和USART3(用他倆舉例)的模式都是設置為Asynchronous，并開啟對應的中斷。
2. RCC的High SPeed CLock模式設置為Crystal/Ceramic
3. 配置對應的時鐘為64Mhz
4. 在main函數中啟動串口1和串口3的空閑中斷模式，接收數據 HAL_UARTEx_ReceiveToIdle_IT(&huart1, rxbuf1, sizeof(rxbuf1));
   HAL_UARTEx_ReceiveToIdle_IT(&huart3, rxbuf3, sizeof(rxbuf3));
5. 在void HAL_UARTEx_RxEventCallback(UART_HandleTypeDef* huart, uint16_t Size)寫對應的透傳即可

• 代碼示例

#include "main.h"
#include <string.h>UART_HandleTypeDef huart1; // 定義串口1的句柄
UART_HandleTypeDef huart3; // 定義串口3的句柄char rxbuf1[128] = {0}; // 用于接收串口1數據的緩沖區
char rxbuf3[128] = {0}; // 用于接收串口3數據的緩沖區
uint8_t uart1_to_uart3_enable = 1;  // 控制串口1是否允許發送數據到串口3的標志位
uint8_t uart3_to_uart1_enable = 1;  // 控制串口3是否允許發送數據到串口1的標志位/*** @brief 串口接收中斷回調函數* 該函數在接收到數據后觸發，并根據當前接收的是串口1還是串口3的數據，進行對應的處理。* @param huart 串口句柄* @param Size 接收到的數據大小*/
void HAL_UARTEx_RxEventCallback(UART_HandleTypeDef* huart, uint16_t Size)
{printf("HAL_UARTEx_RxEventCallback triggered\n");// 判斷當前接收的數據是否來自串口1，并且標志位允許發送給串口3if (huart == &huart1 && uart1_to_uart3_enable){uart3_to_uart1_enable = 0; // 禁止串口3將數據回傳給串口1，防止死循環HAL_UART_Transmit(&huart3, (uint8_t*)rxbuf1, Size, HAL_MAX_DELAY); // 將串口1接收的數據發送給串口3memset(rxbuf1, 0, sizeof(rxbuf1)); // 清空串口1接收緩沖區HAL_UARTEx_ReceiveToIdle_IT(&huart1, rxbuf1, sizeof(rxbuf1)); // 重新啟動串口1接收中斷uart3_to_uart1_enable = 1; // 允許串口3傳輸數據到串口1printf("port1 sent to port 3\n");}// 判斷當前接收的數據是否來自串口3，并且標志位允許發送給串口1else if (huart == &huart3 && uart3_to_uart1_enable){uart1_to_uart3_enable = 0; // 禁止串口1將數據回傳給串口3，防止死循環HAL_UART_Transmit(&huart1, (uint8_t*)rxbuf3, Size, HAL_MAX_DELAY); // 將串口3接收的數據發送給串口1memset(rxbuf3, 0, sizeof(rxbuf3)); // 清空串口3接收緩沖區HAL_UARTEx_ReceiveToIdle_IT(&huart3, rxbuf3, sizeof(rxbuf3)); // 重新啟動串口3接收中斷uart1_to_uart3_enable = 1; // 允許串口1傳輸數據到串口3printf("port3 sent to port 1\n");}return;
}/*** @brief 重定向printf函數，將其輸出重定向到串口1* @param ch 需要輸出的字符* @return 返回輸出的字符*/
int __io_putchar(int ch)
{HAL_UART_Transmit(&huart1, (unsigned char*)&ch, 1, HAL_MAX_DELAY); // 將字符通過串口1發送return ch; // 返回字符
}/*** @brief 主函數*/
int main(void)
{HAL_Init(); // 初始化HAL庫SystemClock_Config(); // 配置系統時鐘MX_GPIO_Init(); // 初始化GPIOMX_USART1_UART_Init(); // 初始化串口1MX_USART3_UART_Init(); // 初始化串口3// 啟動串口1和串口3的空閑中斷模式，接收數據HAL_UARTEx_ReceiveToIdle_IT(&huart1, rxbuf1, sizeof(rxbuf1));HAL_UARTEx_ReceiveToIdle_IT(&huart3, rxbuf3, sizeof(rxbuf3));while (1){// 主循環中可以進行其他任務處理}
}/*** @brief 配置系統時鐘* 設置MCU的時鐘源、倍頻系數等，保證系統運行在正確的時鐘頻率*/
void SystemClock_Config(void)
{RCC_OscInitTypeDef RCC_OscInitStruct = {0}; // 配置RCC振蕩器參數RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; // 配置RCC時鐘源及分頻系數RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; // 使用外部高速振蕩器（HSE）RCC_OscInitStruct.HSEState = RCC_HSE_ON; // 開啟HSERCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1; // HSE預分頻值為1RCC_OscInitStruct.HSIState = RCC_HSI_ON; // 開啟內部高速振蕩器（HSI）RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; // 開啟PLLRCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; // PLL時鐘源為HSERCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL8; // PLL倍頻系數為8if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK){Error_Handler(); // 時鐘配置失敗，進入錯誤處理函數}RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2; // 配置不同的時鐘類型RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 系統時鐘源設置為PLLRCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // AHB時鐘不分頻RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // APB1時鐘分頻系數為2RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // APB2時鐘不分頻if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK){Error_Handler(); // 時鐘配置失敗，進入錯誤處理函數}
}/*** @brief 初始化串口1* 配置波特率、數據位、停止位等串口參數*/
static void MX_USART1_UART_Init(void)
{huart1.Instance = USART1; // 設置串口1的實例huart1.Init.BaudRate = 115200; // 波特率設置為115200huart1.Init.WordLength = UART_WORDLENGTH_8B; // 數據位長度為8位huart1.Init.StopBits = UART_STOPBITS_1; // 停止位為1位huart1.Init.Parity = UART_PARITY_NONE; // 無校驗位huart1.Init.Mode = UART_MODE_TX_RX; // 使能接收和發送模式huart1.Init.HwFlowCtl = UART_HWCONTROL_NONE; // 不使用硬件流控huart1.Init.OverSampling = UART_OVERSAMPLING_16; // 過采樣設置為16倍if (HAL_UART_Init(&huart1) != HAL_OK){Error_Handler(); // 初始化失敗，進入錯誤處理函數}
}/*** @brief 初始化串口3* 配置波特率、數據位、停止位等串口參數*/
static void MX_USART3_UART_Init(void)
{huart3.Instance = USART3; // 設置串口3的實例huart3.Init.BaudRate = 115200; // 波特率設置為115200huart3.Init.WordLength = UART_WORDLENGTH_8B; // 數據位長度為8位huart3.Init.StopBits = UART_STOPBITS_1; // 停止位為1位huart3.Init.Parity = UART_PARITY_NONE; // 無校驗位huart3.Init.Mode = UART_MODE_TX_RX; // 使能接收和發送模式huart3.Init.HwFlowCtl = UART_HWCONTROL_NONE; // 不使用硬件流控huart3.Init.OverSampling = UART_OVERSAMPLING_16; // 過采樣設置為16倍if (HAL_UART_Init(&huart3) != HAL_OK){Error_Handler(); // 初始化失敗，進入錯誤處理函數}
}/*** @brief GPIO初始化* 配置GPIO端口，用于其他硬件外設，如LED、按鍵等*/
static void MX_GPIO_Init(void)
{GPIO_InitTypeDef GPIO_InitStruct = {0};// 啟用GPIO時鐘__HAL_RCC_GPIOD_CLK_ENABLE();__HAL_RCC_GPIOB_CLK_ENABLE();__HAL_RCC_GPIOC_CLK_ENABLE();__HAL_RCC_GPIOA_CLK_ENABLE();// 配置PC6、PC7、PC8引腳為推挽輸出模式，初始化為低電平，用于驅動LED或其他外設HAL_GPIO_WritePin(GPIOC, GPIO_PIN_6 | GPIO_PIN_7 | GPIO_PIN_8, GPIO_PIN_RESET);GPIO_InitStruct.Pin = GPIO_PIN_6 | GPIO_PIN_7 | GPIO_PIN_8; // 設置要配置的引腳GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; // 配置為推挽輸出模式GPIO_InitStruct.Pull = GPIO_NOPULL; // 不使用上拉或下拉電阻GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; // 設置為低速HAL_GPIO_Init(GPIOC, &GPIO_InitStruct); // 初始化GPIO端口PC6、PC7、PC8
}/*** @brief 錯誤處理函數* 當系統發生錯誤時調用該函數?？梢栽诖撕瘮?shù)中添加錯誤處理邏輯，如重啟系統或記錄日志。*/
void Error_Handler(void)
{__disable_irq(); // 禁用全局中斷，防止進一步的干擾while (1) {// 無限循環，防止系統繼續運行。可以在此添加LED閃爍等故障指示}
}#ifdef USE_FULL_ASSERT
/*** @brief 斷言失敗時調用此函數* 當遇到斷言參數錯誤時，報告源文件和行號，幫助調試* @param file 指向發生錯誤的源文件名的指針* @param line 發生錯誤的代碼行號*/
void assert_failed(uint8_t *file, uint32_t line)
{// 可以在此添加打印或記錄錯誤的實現，例如：// printf("Wrong parameters value: file %s on line %d\r\n", file, line);
}
#endif /* USE_FULL_ASSERT */

ESP8266與STM32

• ESP8266 是一款集成了Wi-Fi通信功能的低功耗微控制器，廣泛應用于物聯網（IoT）設備中。
• Station 模式：可以像普通的 Wi-Fi 設備一樣連接到現有的無線網絡。
• AP 模式：可以創建自己的 Wi-Fi 熱點，讓其他設備連接到 ESP8266。
• Station + Access Point 混合模式（STA + AP 模式）:ESP8266 同時充當客戶端和熱點，既可以連接到現有的 Wi-Fi 網絡（作為 STA），又可以作為熱點允許其他設備連接到它（作為 AP）。

AT+CWMODE=1：設置為 Station 模式。
AT+CWMODE=2：設置為 AP 模式。
AT+CWMODE=3：設置為 STA + AP 混合模式。

• 服務器

www.daxia.com//下載SSCOM即可

STATION模式

• 配置uart1- printf，uart3-esp上網（因為WiFi芯片在串口3）
  

使用方法

• 新建stm32工程中添加WiFi-ops.c和WiFi-ops.h
• 開啟時鐘頻率為64Mhz和RCC的Crystal
• 開啟UART1和UART3串口為異步通信，且開啟中斷。
• 并配置LED燈管腳留作測試
• 代碼示例

#include "main.h"
#include "stdio.h"
#include "string.h"
#include "wifi-ops.h"// UART句柄
UART_HandleTypeDef huart1;
UART_HandleTypeDef huart3;void SystemClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_USART1_UART_Init(void);
static void MX_USART3_UART_Init(void);
// 日志狀態標志
int log_success_flags = 0;  // 0 - 未初始化，1 - 日志成功，2 - 日志失敗/*** @brief  ESP8266 Station模式回調函數* @param  data: 接收到的數據* @param  len: 數據長度* @retval 返回值說明*/
int esp_station_callback(char *data, int len)
{printf("recv from serv: %s\r\n", data);// 更新日志狀態標志if (strstr(data, "log success")) {log_success_flags = 1;} else if (strstr(data, "log failed")) {log_success_flags = 2;}return 0;
}/*** @brief  UART接收事件回調函數* @param  huart: UART句柄* @param  Size: 接收的數據大小* @retval None*/
void HAL_UARTEx_RxEventCallback(UART_HandleTypeDef *huart, uint16_t Size)
{// 處理接收事件，沒有傳給另一個串口wifi_uart_prepare_idle(huart);  // 接收完成后，準備UART進行下一次接收
}/*** @brief  重定向putchar到UART1* @param  ch: 要發送的字符* @retval 返回發送的字符*/
int __io_putchar(int ch)
{HAL_UART_Transmit(&huart1, (unsigned char *)&ch, 1, 1);return ch;
}/*** @brief  主函數入口* @retval 程序返回值*/
int main(void)
{HAL_Init(); // 初始化HAL庫SystemClock_Config(); // 配置系統時鐘// 初始化所有配置的外設MX_GPIO_Init();MX_USART1_UART_Init();MX_USART3_UART_Init();int ret;char sendbuf[128] = {0}; // 用于發送數據的緩沖區// 準備UART3進行ESP8266通信，使用串口3wifi_uart_prepare_idle(&huart3);// 初始化ESP8266 Station模式，使用串口3ret = wifi_station_init(&huart3, esp_station_callback);if (ret < 0) {printf("%s-%d wifi_station_init err\r\n", __func__, __LINE__);return -35;}// 連接到指定的APret = wifi_station_join_ap(&huart3, "xiaomimobile", "12345600");if (ret < 0) {printf("%s-%d wifi_station_join_ap err\r\n", __func__, __LINE__);return -35;}// 連接到指定的TCP服務器ret = wifi_station_tcp_connect(&huart3, "107.148.201.156", 10005);if (ret < 0) {printf("%s-%d wifi_station_tcp_connect err\r\n", __func__, __LINE__);return -35;}// 發送日志請求數據。特定格式snprintf(sendbuf, sizeof(sendbuf), "toServ:action=log,usrname=%s,passwd=%s,devname=sml001;", "xiaowang", "123456");ret = wifi_station_tcp_send_data(&huart3, sendbuf, strlen(sendbuf));if (ret < 0) {printf("%s-%d wifi_station_tcp_send_data err\r\n", __func__, __LINE__);}// 等待日志發送結果for (int i = 0; i < 50; i++) {if (log_success_flags == 2) {printf("%s-%d log failed \r\n", __func__, __LINE__);return -23;} else if (log_success_flags == 1) {printf("%s-%d log success \r\n", __func__, __LINE__);break;}HAL_Delay(10);}// 循環發送獲取時間請求，這個是該服務器的特定格式strcpy(sendbuf, "toServ:action=gettime;");while (1){ret = wifi_station_tcp_send_data(&huart3, sendbuf, strlen(sendbuf));if (ret < 0) {printf("%s-%d wifi_station_tcp_send_data err\r\n", __func__, __LINE__);}HAL_Delay(500); // 等待500毫秒}
}/*** @brief  配置系統時鐘* @retval None*/
void SystemClock_Config(void)
{RCC_OscInitTypeDef RCC_OscInitStruct = {0};RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};// 初始化RCC振蕩器RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;RCC_OscInitStruct.HSEState = RCC_HSE_ON;RCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1;RCC_OscInitStruct.HSIState = RCC_HSI_ON;RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL8;if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {Error_Handler();}// 初始化CPU、AHB和APB總線時鐘RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK) {Error_Handler();}
}/*** @brief  初始化USART1* @retval None*/
static void MX_USART1_UART_Init(void)
{huart1.Instance = USART1;huart1.Init.BaudRate = 115200;huart1.Init.WordLength = UART_WORDLENGTH_8B;huart1.Init.StopBits = UART_STOPBITS_1;huart1.Init.Parity = UART_PARITY_NONE;huart1.Init.Mode = UART_MODE_TX_RX;huart1.Init.HwFlowCtl = UART_HWCONTROL_NONE;huart1.Init.OverSampling = UART_OVERSAMPLING_16;if (HAL_UART_Init(&huart1) != HAL_OK) {Error_Handler();}
}/*** @brief  初始化USART3* @retval None*/
static void MX_USART3_UART_Init(void)
{huart3.Instance = USART3;huart3.Init.BaudRate = 115200;huart3.Init.WordLength = UART_WORDLENGTH_8B;huart3.Init.StopBits = UART_STOPBITS_1;huart3.Init.Parity = UART_PARITY_NONE;huart3.Init.Mode = UART_MODE_TX_RX;huart3.Init.HwFlowCtl = UART_HWCONTROL_NONE;huart3.Init.OverSampling = UART_OVERSAMPLING_16;if (HAL_UART_Init(&huart3) != HAL_OK) {Error_Handler();}
}/*** @brief  初始化GPIO* @retval None*/
static void MX_GPIO_Init(void)
{GPIO_InitTypeDef GPIO_InitStruct = {0};// 啟用GPIO端口時鐘__HAL_RCC_GPIOD_CLK_ENABLE();__HAL_RCC_GPIOB_CLK_ENABLE();__HAL_RCC_GPIOC_CLK_ENABLE();__HAL_RCC_GPIOA_CLK_ENABLE();// 配置GPIO輸出級別HAL_GPIO_WritePin(GPIOC, GPIO_PIN_6 | GPIO_PIN_7 | GPIO_PIN_8, GPIO_PIN_RESET);// 配置GPIO引腳GPIO_InitStruct.Pin = GPIO_PIN_6 | GPIO_PIN_7 | GPIO_PIN_8;GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;GPIO_InitStruct.Pull = GPIO_NOPULL;GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
}/*** @brief  錯誤處理函數* @retval None*/
void Error_Handler(void)
{__disable_irq();while (1) {}
}/*** @brief  報告斷言失敗的文件名和行號* @param  file: 源文件名* @param  line: 錯誤行號* @retval None*/
void assert_failed(uint8_t *file, uint32_t line)
{// 用戶可以添加自己的實現來報告文件名和行號
}

混合模式

• 默認情況下，ESP8266 的 IP 地址在 AP 模式下是 192.168.4.1，以便其他設備連接到該 AP 時可以進行通信。
• 代碼

#include "main.h"#include "stdio.h"
#include "string.h"
#include "wifi-ops.h"UART_HandleTypeDef huart1;
UART_HandleTypeDef huart3;void SystemClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_USART1_UART_Init(void);
static void MX_USART3_UART_Init(void);#ifdef ESP_STATION/*當stm32收到 esp/服務器發來消息, 會自動執行該函數* 	data,len 表示收到的具體數據和長度*** 該函數是在 中斷執行,不好執行耗時/睡眠工作* */int log_success_flags = 0;		//0-uninit  1-log  2-failedint esp_station_callback (char *data,int len)
{printf("recv from serv: %s\r\n",data);//登陸成功失敗標志位if( strstr(data,"log success") ){log_success_flags = 1;}else if(strstr(  data, "log failed")){log_success_flags = 2;}}
#endif/* 希望手機發來消息,該函數 被調用,  data len分別是對方發來的消息和長度*/
int esp_ap_callback(char *data,int len)
{printf("recv from phone: %s\r\n",data);		//cmd:wifiname=hyx,wifipasswd=8888888,usrname=xiaowang,passwd=123456;
}void HAL_UARTEx_RxEventCallback(UART_HandleTypeDef *huart, uint16_t Size)
{//other thing to dowifi_uart_prepare_idle(huart);	//after recv success, wo must prepare uart for next time
}int __io_putchar(int ch)
{HAL_UART_Transmit(&huart1, (unsigned char *)&ch,  1,     1);return ch;
}int main(void)
{HAL_Init();SystemClock_Config();MX_GPIO_Init();MX_USART1_UART_Init();MX_USART3_UART_Init();/* USER CODE BEGIN 2 */int ret;int linkid;	//每個手機都可以連接ap,都會安排一個idchar sendbuf[128]={0};#ifdef ESP_STATION//預處理uart3 for esp ...wifi_uart_prepare_idle(&huart3);ret = wifi_station_init(&huart3,  esp_station_callback );if(ret < 0 ){	printf("%s-%d wifi_station_init err\r\n",__func__,__LINE__);		return -35;}ret = wifi_station_join_ap(&huart3,"WANGQINGFA","1234567890");if(ret < 0 ){	printf("%s-%d wifi_station_join_ap err\r\n",__func__,__LINE__);		return -35;}ret = wifi_station_tcp_connect(&huart3,"107.148.201.156",10001);if(ret < 0 ){	printf("%s-%d wifi_station_tcp_connect err\r\n",__func__,__LINE__);	return -35;}/*登陸服務器		toServ:action=log,usrname=xiaowang,passwd=123456,devname=sml001;		*/snprintf(sendbuf,sizeof(sendbuf), "toServ:action=log,usrname=%s,passwd=%s,devname=sml001;","xiaowang","123456" );ret = wifi_station_tcp_send_data(&huart3,sendbuf,strlen(sendbuf));if(ret < 0 ){	printf("%s-%d wifi_station_tcp_connect err\r\n",__func__,__LINE__);	   }for(int i=0;i<50;i++){if(log_success_flags == 2){printf("%s-%d log failed \r\n",__func__,__LINE__);return -23;}else if(log_success_flags == 1){printf("%s-%d log success \r\n",__func__,__LINE__);break;}HAL_Delay(10);}
#endifwifi_uart_prepare_idle(&huart3);ret = wifi_ap_init(&huart3,  esp_ap_callback);if(ret < 0 ){	printf("%s-%d wifi_ap_init err\r\n",__func__,__LINE__);		return -35;}ret = wifi_ap_set_args(&huart3, "zhangsan","12345678");if(ret < 0 ){	printf("%s-%d wifi_ap_set_args err\r\n",__func__,__LINE__);		return -35;}linkid = wifi_ap_tcp_listen_and_wait_connect_timeout(&huart3,10001,     5*60*1000);if(linkid < 0 ){	printf("%s-%d wifi_ap_tcp_listen_and_wait_connect_timeout err\r\n",__func__,__LINE__);		return -35;}/* USER CODE END 2 *//* Infinite loop *//* USER CODE BEGIN WHILE */strcpy(sendbuf,"cmd:hello phone,I have got you messgae,please reset it;");while (1){wifi_ap_tcp_send_data(&huart3, linkid , sendbuf,strlen(sendbuf)    );#ifdef ESP_STATIONret = wifi_station_tcp_send_data(&huart3,sendbuf,strlen(sendbuf));if(ret < 0 ){	printf("%s-%d wifi_station_tcp_connect err\r\n",__func__,__LINE__);	   }
#endifHAL_Delay(500);/* USER CODE END WHILE *//* USER CODE BEGIN 3 */}/* USER CODE END 3 */
}/*** @brief System Clock Configuration* @retval None*/
void SystemClock_Config(void)
{RCC_OscInitTypeDef RCC_OscInitStruct = {0};RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};/** Initializes the RCC Oscillators according to the specified parameters* in the RCC_OscInitTypeDef structure.*/RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;RCC_OscInitStruct.HSEState = RCC_HSE_ON;RCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1;RCC_OscInitStruct.HSIState = RCC_HSI_ON;RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL8;if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK){Error_Handler();}/** Initializes the CPU, AHB and APB buses clocks*/RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK){Error_Handler();}
}/*** @brief USART1 Initialization Function* @param None* @retval None*/
static void MX_USART1_UART_Init(void)
{/* USER CODE BEGIN USART1_Init 0 *//* USER CODE END USART1_Init 0 *//* USER CODE BEGIN USART1_Init 1 *//* USER CODE END USART1_Init 1 */huart1.Instance = USART1;huart1.Init.BaudRate = 115200;huart1.Init.WordLength = UART_WORDLENGTH_8B;huart1.Init.StopBits = UART_STOPBITS_1;huart1.Init.Parity = UART_PARITY_NONE;huart1.Init.Mode = UART_MODE_TX_RX;huart1.Init.HwFlowCtl = UART_HWCONTROL_NONE;huart1.Init.OverSampling = UART_OVERSAMPLING_16;if (HAL_UART_Init(&huart1) != HAL_OK){Error_Handler();}}static void MX_USART3_UART_Init(void)
{huart3.Instance = USART3;huart3.Init.BaudRate = 115200;huart3.Init.WordLength = UART_WORDLENGTH_8B;huart3.Init.StopBits = UART_STOPBITS_1;huart3.Init.Parity = UART_PARITY_NONE;huart3.Init.Mode = UART_MODE_TX_RX;huart3.Init.HwFlowCtl = UART_HWCONTROL_NONE;huart3.Init.OverSampling = UART_OVERSAMPLING_16;if (HAL_UART_Init(&huart3) != HAL_OK){Error_Handler();}/* USER CODE BEGIN USART3_Init 2 *//* USER CODE END USART3_Init 2 */}/*** @brief GPIO Initialization Function* @param None* @retval None*/
static void MX_GPIO_Init(void)
{GPIO_InitTypeDef GPIO_InitStruct = {0};/* GPIO Ports Clock Enable */__HAL_RCC_GPIOD_CLK_ENABLE();__HAL_RCC_GPIOB_CLK_ENABLE();__HAL_RCC_GPIOC_CLK_ENABLE();__HAL_RCC_GPIOA_CLK_ENABLE();/*Configure GPIO pin Output Level */HAL_GPIO_WritePin(GPIOC, GPIO_PIN_6|GPIO_PIN_7|GPIO_PIN_8, GPIO_PIN_RESET);/*Configure GPIO pins : PC6 PC7 PC8 */GPIO_InitStruct.Pin = GPIO_PIN_6|GPIO_PIN_7|GPIO_PIN_8;GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;GPIO_InitStruct.Pull = GPIO_NOPULL;GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);}/* USER CODE BEGIN 4 *//* USER CODE END 4 *//*** @brief  This function is executed in case of error occurrence.* @retval None*/
void Error_Handler(void)
{__disable_irq();while (1){}/* USER CODE END Error_Handler_Debug */
}#ifdef  USE_FULL_ASSERT
/*** @brief  Reports the name of the source file and the source line number*         where the assert_param error has occurred.* @param  file: pointer to the source file name* @param  line: assert_param error line source number* @retval None*/
void assert_failed(uint8_t *file, uint32_t line)
{/* USER CODE BEGIN 6 *//* User can add his own implementation to report the file name and line number,ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) *//* USER CODE END 6 */
}
#endif /* USE_FULL_ASSERT */

• 如圖所示，用的TCP/IP調試軟件