設計做兼職最好的網站如何優化搜索引擎
組網需求
說明
S5720I-10X-PWH-SI-AC 和 S5720I-6X-PWH-SI-AC 不支持此配置。
如 圖 3-23 所示，為了增加設備的容量采用設備堆疊技術，將 Switch3 和 Switch4通過專用的堆疊電纜鏈接起來，對外呈現為一臺邏輯交換機。為了實現設備間的備份、提高可靠性，采用跨堆疊設備Eth-Trunk接口技術，將不同設備上的物理接口加入同一個Eth-Trunk接口。在網絡無任何故障情況下，在PE設備上查看成員口信息時，發現VLAN2的數據流量會通過成員口GE1/0/1和GE1/0/2轉發，VLAN3的數據流量通過成員口GE1/0/1和GE1/0/2轉發。增加了堆疊設備之間的帶寬承載能力，也降低了流量轉發效率。為了有效保證VLAN2的數據流量通過成員口GE1/0/1轉發，VLAN3的數據流量通過成員口GE1/0/2轉發，可在堆疊設備上使能Eth-Trunk接口流量本地優先轉發功能。
配置思路
采用如下的思路配置 Eth-Trunk 接口流量本地優先轉發功能：
1. 創建 Eth-Trunk 接口。
2. 加入 Eth-Trunk 的成員接口。
3. 使能 Eth-Trunk 接口流量本地優先轉發功能。
4. 配置各接口加入相應 VLAN ，實現二層互通。
操作步驟
步驟 1 創建 Eth-Trunk 接口，并配置允許通過的 VLAN
# 配置 Stack 。
<HUAWEI> system-view
[HUAWEI] sysname Stack
[Stack] interface eth-trunk 10
[Stack-Eth-Trunk10] port link-type trunk
[Stack-Eth-Trunk10] port trunk allow-pass vlan all
[Stack-Eth-Trunk10] undo port trunk allow-pass vlan 1
[Stack-Eth-Trunk10] quit
# 配置 PE 。
<HUAWEI> system-view
[HUAWEI] sysname PE
[PE] interface eth-trunk 10
[PE-Eth-Trunk10] port link-type trunk
[PE-Eth-Trunk10] port trunk allow-pass vlan all
[PE-Eth-Trunk10] undo port trunk allow-pass vlan 1
[PE-Eth-Trunk10] quit
步驟 2 加入 Eth-Trunk 的成員接口
# 配置 Stack 。
[Stack] interface gigabitethernet 1/0/4
[Stack-GigabitEthernet1/0/4] eth-trunk 10
[Stack-GigabitEthernet1/0/4] quit
[Stack] interface gigabitethernet 2/0/4
[Stack-GigabitEthernet2/0/4] eth-trunk 10
[Stack-GigabitEthernet2/0/4] quit
# 配置 PE 。
[PE] interface gigabitethernet 1/0/1
[PE-GigabitEthernet1/0/1] eth-trunk 10
[PE-GigabitEthernet1/0/1] quit
[PE] interface gigabitethernet 1/0/2
[PE-GigabitEthernet1/0/2] eth-trunk 10
[PE-GigabitEthernet1/0/2] quit
步驟 3 在堆疊設備上使能 Eth-Trunk 接口流量本地優先轉發功能
對于 S2730S-S 、 S5735-L-I 、 S5735-L1 、 S300 、 S5735-L 、 CloudEngine S5735S-L1 、
S5735S-L 、 S5735-S 、 S5735S-S 、 S5735S-L-M 、 S500 ：
[Stack] local-preference enable
對于除 S2730S-S 、 S5735-L-I 、 S5735-L1 、 S300 、 S5735-L 、 CloudEngine S5735S
L1 、 S5735S-L 、 S5735-S 、 S5735S-S 、 S5735S-L-M 、 S500 之外的設備：
[Stack] interface eth-trunk 10
[Stack-Eth-Trunk10] local-preference enable
[Stack-Eth-Trunk10] quit
步驟 4 配置二層轉發功能
# 配置 Stack 。
[Stack] vlan batch 2 3
[Stack] interface gigabitethernet 1/0/3
[Stack-GigabitEthernet1/0/3] port link-type trunk
[Stack-GigabitEthernet1/0/3] port trunk allow-pass vlan 2
[Stack-GigabitEthernet1/0/3] undo port trunk allow-pass vlan 1
[Stack-GigabitEthernet1/0/3] quit
[Stack] interface gigabitethernet 2/0/3
[Stack-GigabitEthernet2/0/3] port link-type trunk
[Stack-GigabitEthernet2/0/3] port trunk allow-pass vlan 3
[Stack-GigabitEthernet2/0/3] undo port trunk allow-pass vlan 1
[Stack-GigabitEthernet2/0/3] quit
# 配置 Switch1 。
<HUAWEI> system-view
[HUAWEI] sysname Switch1
[Switch1] vlan 2
[Switch1-vlan2] quit
[Switch1] interface gigabitethernet 0/0/1
[Switch1-GigabitEthernet0/0/1] port link-type trunk
[Switch1-GigabitEthernet0/0/1] port trunk allow-pass vlan 2
[Switch1-GigabitEthernet0/0/1] undo port trunk allow-pass vlan 1
[Switch1-GigabitEthernet0/0/1] quit
[Switch1] interface gigabitethernet 0/0/2
[Switch1-GigabitEthernet0/0/2] port link-type trunk
[Switch1-GigabitEthernet0/0/2] port trunk allow-pass vlan 2
[Switch1-GigabitEthernet0/0/2] undo port trunk allow-pass vlan 1
[Switch1-GigabitEthernet0/0/2] quit
# 配置 Switch2 。
<HUAWEI> system-view
[HUAWEI] sysname Switch2
[Switch2] vlan 3
[Switch2-vlan3] quit
[Switch2] interface gigabitethernet 0/0/1
[Switch2-GigabitEthernet0/0/1] port link-type trunk
[Switch2-GigabitEthernet0/0/1] port trunk allow-pass vlan 3
[Switch2-GigabitEthernet0/0/1] undo port trunk allow-pass vlan 1
[Switch2-GigabitEthernet0/0/1] quit
[Switch2] interface gigabitethernet 0/0/2
[Switch2-GigabitEthernet0/0/2] port link-type trunk
[Switch2-GigabitEthernet0/0/2] port trunk allow-pass vlan 3
[Switch2-GigabitEthernet0/0/2] undo port trunk allow-pass vlan 1
[Switch2-GigabitEthernet0/0/2] quit
步驟 5 檢查配置結果
上述配置成功后，在任意視圖下執行命令 display trunkmembership eth-trunk ，可
以看到 Eth-Trunk 接口的成員口信息。例如：
以 Stack 的顯示為例。
<Stack> display trunkmembership eth-trunk 10
Trunk ID: 10
Used status: VALID
TYPE: ethernet
Working Mode : Normal
Number Of Ports in Trunk = 2
Number Of Up Ports in Trunk = 2
Operate status: up
Interface GigabitEthernet1/0/4, valid, operate up, weight=1
Interface GigabitEthernet2/0/4, valid, operate up, weight=1
---- 結束
配置文件
● Stack 的配置文件
#
sysname Stack
#
vlan batch 2 3
#
interface Eth-Trunk10
port link-type trunk
undo port trunk allow-pass vlan 1
port trunk allow-pass vlan 2 to 4094
#
interface GigabitEthernet1/0/3
port link-type trunk
undo port trunk allow-pass vlan 1
port trunk allow-pass vlan 2
#
interface GigabitEthernet2/0/3
port link-type trunk
undo port trunk allow-pass vlan 1
port trunk allow-pass vlan 3
#
interface GigabitEthernet1/0/4
eth-trunk 10
#
interface GigabitEthernet2/0/4
eth-trunk 10
#
return
● PE 的配置文件
#
sysname PE
#
interface Eth-Trunk10
port link-type trunk
undo port trunk allow-pass vlan 1
port trunk allow-pass vlan 2 to 4094
#
interface GigabitEthernet1/0/1
eth-trunk 10
#
interface GigabitEthernet1/0/2
eth-trunk 10
#
return
● Switch1 的配置文件
#
sysname Switch1
#
vlan batch 2
#
interface GigabitEthernet0/0/1
port link-type trunk
undo port trunk allow-pass vlan 1
port trunk allow-pass vlan 2
#
interface GigabitEthernet0/0/2
port link-type trunk
undo port trunk allow-pass vlan 1
port trunk allow-pass vlan 2
#
return
● Switch2 的配置文件
#
sysname Switch2
#
vlan batch 3
#
interface GigabitEthernet0/0/1
port link-type trunk
undo port trunk allow-pass vlan 1
port trunk allow-pass vlan 3
#
interface GigabitEthernet0/0/2
port link-type trunk
undo port trunk allow-pass vlan 1
port trunk allow-pass vlan 3
#
return